/https%3A%2F%2Fblog.ofbusiness.com%2Fwp-content%2Fuploads%2F2016%2F04%2F16.jpg)
As of the end of last year, the steel industry in India was under the challenge of worsening steel prices and it was not the only affected. The world all over was under a similar challenge. And the main cause of it was due to increased imports from the worldโs leading producer, China. Late last year, we witnessed the market undergoing little improvements through the first half of the year.
Domestic steel industries were at first under intense crisis, as we saw most of them shutting down as china continued to multiply its supply to India. But today, the industry is placing its bets on the increasing domestic demand as it works to counter the import glut and predatory pricing that challenged the industry in 2015.
In the middle of the growing domestic demand and spectre of lowly priced steel from China flooding the global markets, analysts predict that the global steel industry for 2016 is not going to get better sooner. However, the case for India is little bit different as the growing domestic demand and the governmentโs move is going to set the market more profitable as compared to the Asian peers.
2015 was a tough year for the entire world, including US and Europe as the commodityโs prices were faced by deflation which brought the prices down. As in the context of India, the drop in price was rather steeper even more than the raw materials. This led to a great pressure on the operating margins of countryโs steel plants.
The threat on India, even though still lingering, was powered by the weaker domestic demand in the major producers of steel in Asia such as China, South Korea and Japan. This caused them to shift their focus more on exports at unduly prices on India, US and Europe. This adversely affected the domestic steel industries. The effect led to some of the steel product prices hitting the lowest prices in ten years in the Indian market.
The poor price predation and excessive imports combined to jeopardise the huge amount of loans which had been raised by the local steel companies to undertake capacity expansion. This situation reflected back on financial health of a number of Indiaโs largest banks. By the end of 2015, the steel industry of India was a great contributor to bad loan problems and Non-Performing Assets of banks.
The steel industry is not only tense in India, but worldwide. However, the Indian industry is deemed much better this year as compared with other countries such as China. Consumption as well as production this year is increasing as reported by Narendra Singh Tomar, the Steel Minister early this year.
The government is also looking after the interest of domestic players, either small or big, by introduction of Minimum Import Price. The introduction of safeguard duties by the government is going to make the increased exports from China have modest positive influence on the local producersโ profitability.ย Even though the global crisis of steel industry is not expected to better soon, the Indian steel industry is set to perform much better than its peers.
/https%3A%2F%2Fblog.ofbusiness.com%2Fwp-content%2Fuploads%2F2026%2F07%2FTemplate-OFb-33.png)
TL;DR: MS angle and MS channel are both hot-rolled structural steel sections, but they are not interchangeable. Angles suit bracing and lightweight framing, while channels carry higher loads across a span. This guide compares their standards, weight, cost, and buying process so fabricators and contractors pick the right section on OFB. MS angle and MS
/https%3A%2F%2Fblog.ofbusiness.com%2Fwp-content%2Fuploads%2F2026%2F06%2Funnamed.png)
TL;DR: TMT bar grades under IS 1786 run from Fe415 to Fe600, each defined by minimum yield strength and ductility. Grade selection depends on structural load, seismic zone, and project type. This guide helps construction buyers and procurement teams compare all six grades and source verified TMT bars through OFB. Indian construction projects specify TMT
/https%3A%2F%2Fblog.ofbusiness.com%2Fwp-content%2Fuploads%2F2026%2F07%2FTemplate-OFb-31.png)
TL;DR: India Steel Sector grew steadily in Q1 FY 2026-27, with higher production, consumption and imports of finished steel. Prices softened slightly in June across TMT bars, HR coils and other steel products, though they remain higher than last year. This report helps construction and manufacturing buyers plan bulk purchases, track price trends, and source